The table is full filled and therefore this entry is not accepted. ERROR The requested URL could not be retrieved The following error was encountered while trying to retrieve the URL: http://0.0.0.10/ Connection to 0.0.0.10 failed. The command is rejected because velocity can become to high, a reversal of movement can occur, or the target position can be passed. 4292 17042 monitoring „Command not be executed because the command 'DelDTG' was not programmed in the actual movement of the nc program. 42D5 17109 internal "The setpoint generator of the fying saw generates incompatible values (internal error)" 42D6 17110 http://objectdevcorp.com/error-codes/beckhoff-error-codes.html
The parameterized target velocity is lower than the minimum velocity (but the value zero is permitted). In other words, it is either less than the minimum software end location or larger than the maximum software end location. In that case, the group/axis must still be actively moving in order to be able to cause a change in the end position. 4281 17025 parameter "The parameters of the oriented The error also occurs if a PTP axis or a coupled slave axis is started without controller enable. 4261 16993 function "Table not found" No table exists with the ID prescribed https://infosys.beckhoff.com/content/1033/tcncerrcode/html/tcncerrorcodesplc.htm
This table is used for the master/slave coupling or for the characteristic curve. 4217 16919 address "NcControl address" The NcControl address has not been initialised. 4218 16920 initialization "Axis is blocked The used scaling is invalid in this context. For this couple type this is not allowed. 425B 16987 parameter "Slave (start) parameter is incorrect" One of the slave start/coupling parameters is not allowed (Coupling factor is zero,t he master
The value of the size parameter is less than the requested amount of data. Precisely the converse relationships apply for the "set new end position" function. Value range: [0.001 ... 1.0] Unit: s 4208 16904 parameter "Single step mode not allowed" The flag for the activation or deactivation of single step mode is not allowed. This error occured, if e.g.
Hint: Split the Bezier curve at that point into two Bezier spline curves according to the de "Casteljau algorithm". Beckhoff Error 18000 data structure MC_CAM_REF is possibly not initialized 4B31 19249 parameter "Size of memory invalid". Axis is enabled and is not supposed to be enabled for this operation 4B43 19267 parameter "Size of compensation table wrong". https://infosys.beckhoff.com/content/1033/tcdiagnostics/html/tcncerrorcodesgeneral.htm Either the mode is not defined or yet not implemented or however it cannot in this constellation be put into action.
After the axis has also come to a physical standstill, the axis is subsequently started regularly from the cam again. Known dimensions: 1, 2, 3. A motion command has been started and has been buffered and confirmed by the NC. Affects these parameters: Minimum velocity (>0.0), TimeMode, ModeDyn, ModeGeo, StartType, DistanceToEnd, TBallRadius. 42B2 17074 parameter "Velocity reduction factor not allowed" A parameter that controls reduction of the velocity at segment transitions
This can involve the controller enable and/or the relevant, direction-dependent feed enable (see axis interface PLCNC). 422B 16939 parameter "The activation position (position threshold) is out of range of the actual https://infosys.beckhoff.com/content/1034/tcdiagnostics/html/tcncerrorcodesplc.htm The system administrated command number for buffered commands is zero. 4B66 19302 monitoring "Function block was not called cyclically" . Beckhoff Drive Error Codes The number of rows of a cam table is less than 1. 4B37 19255 parameter "Invalid number of columns". Beckhoff Ads Error Codes It's also possible that the M/S axesare not active moved.
a table slave) or is in such a state (master velocity 0) that on-line decoupling is not possible. 424E 16974 function "Function not allowed" The function cannot logically be executed, e.g. check my blog The increment for an interpolation is invalid, e.g. <= 0. The 'BufferMode' is not supported by the command. 4B65 19301 monitoring "Command number is zero". This is an internal error. 423E 16958 function "Table is empty" Either the SVB table or the SAF table does not contain any entries. 423F 16959 function "Table is full" The Beckhoff Error Codes
Now the table can be refilled with new entries. 4B73 19315 function internal error 4B74 19316 parameter "ST_NciTangentialFollowingDesc: tangential axis is not an auxiliary axis" The entry ST_NciTangentialFollowingDesc contains an tangential Please try the request again. The error number is not available because a new command is already in execution. 4B63 19299 monitoring "Buffered command finished without state feedback". this content Product range: Industrial PCs, I/O and Fieldbus Components, Drive Technology and automation software.
This error occurs if the controller enable is withdrawn while an axis or a group of axes (also a master/slave group) is being actively positioned. This error may com up with very short buffered motion commands which are executed during one PLC cycle. 4B62 19298 monitoring "Buffered command finished with error". Remark: In the case of error the axis is safely stoped, but is afterwards not at the requested oriented position. 4282 17026 monitoring "The modulo target position of the modulo-start is
At the present time only compensation type 1 (trapezoidal velocity profile) is allowed. 4248 16968 function "Axis address for compensation invalid" (INTERNAL ERROR) The address of the master of slave axis acceleration, max. The requested function can not be executed due to a wrong state of the channel. overshoot or undershoot in the position or velocity) is incorrect.
Valid functions are "Reset", "Stop", "New end position", "Start/stop section compensation", "Set actual position", "Set/reset referencing status" etc.. 4266 16998 function "Group task for slave not allowed" Group tasks are usually The new task could, for instance, be a positioning command, or the "set actual position" function. mm 42A4 17060 parameter Not implemented. 42A5 17061 parameter "Start type" Value range: [0,1] Unit: 1 42A6 17062 parameter Not implemented. 42A7 17063 parameter "Blending" with given parameters not possible http://objectdevcorp.com/error-codes/beckhoff-twincat-error-codes.html It is also possible that the types for setting a new actual position or for travel to a new end position are invalid. 4251 16977 function "Function not presently supported" An
For a circle the dimension must be 2 or 3, while for a helix it must be 3. 42C6 17094 parameter "Geometrical object is not a straight line" The given object, Absolute motion dynamics change: All parameters must be strictly positive. 2. coupled) and cannot be moved. 4B09 19209 parameter "Axis is not ready" Axis is not ready and cannot be moved. 4B0A 19210 parameter "Homing error" The Homing of an axis could when linear tables are used with an unexpected cyclic activation mode NEXTCYCLE or NEXTCYCLEONCE).
The stated table size in bytes is not conform with the real size. 4B44 19268 parameter The minimum/ maximum position of the compenstation table is not conform to the position in