Messages are sent to the on-board microprocessor to perform the following tests. All rights reserved. Verify that the port is a TTI port using either the display port command (the display shows that the port is a TTI port) or the list config command (the display Replaced ethernet cable between CrossFire Adapter and IP switchport. Check This Out
y VLAN: n VLAN: n Network Region: 2 VOIP Channels: 320 IPV4 PARAMETERS Node Name: [rdctd]2a13 IP Address: 10.2.7.14 Duplicate Node Name: [rdctd]2a14 IP Address: 10.2.7.15 Gateway Node Name: [redacted] IP Look in the Error Log for Error Type 18 (port busied out) for this port. TEST #48 Station Present Test Error Code Test Result Description/Recommendation ABORT Necessary system resources could not be allocated to run this test. This can be an indication of communications problems between the Processor and Digital Port Media Module.
Name Type State 1 2 Alarmed Resolved 02A13 IPMEDPRO y MINOR y 02/05/18:17 00/00/00:00 02A13 IPMEDPRO y MINOR y 02/05/18:17 00/00/00:00 02A1302 MEDPROPT y WARNING OUT 02/05/18:17 00/00/00:00 02A1301 MEDPROPT y When troubleshooting problems like these, I generally tend to work in a progression such that I check for administrative/configuration issues, then use software diagnostics (i.e., busyout, test board, etc), then bypass/replace/mitigate The polycom ports never have this problem. I removed the existing CrossFire Adapter, and replaced it with a spare.
Re-checked IP switchport configuration. Avaya Error Code 1392 If this is the case, the board is shut down. Dave - [-] Test 48 November 18, 2010 08:31 AM (in response to Tom McGuire) That's what I thought, thanks for the reply. https://support.avaya.com/public/index?page=content&id=SOLN244102&pmv=print&impressions=false Retry the command at 1-minute intervals up to 3 times.
If the port is busied out: Issue release access-endpoint
Name Test No. https://support.avaya.com/elmodocs2/s8700/cmain/MaintenanceChapter06130.html CM is able to test equipment on-demand, so that you can see which tests have failed (and resulted in the aforementioned errors): test board 02a13 long Page 1 TEST RESULTS Port Avaya Error Code 1412 I have also for the most part discovered that if I remove the cable from V501 that connects the paging system to the phone system, the phones remain "up". Avaya Error Codes List The port may be busy with a valid call.
What can this be? http://objectdevcorp.com/error-code/aws-error-codes.html Join UsClose Joe22 Ashish Mishra [Orange] Need Help with Error Code November 14, 2011 03:02 PM (in response to Charles Young) BTW, what is the exact problem you`re facing with MM711 analog mm Close Reply To This Thread Posting in the Tek-Tips forums is a member-only feature.
Check to make sure that the board translations are correct. This test may cause some terminal equipment to ring briefly during daily maintenance. Issue the reset board GGGVS command. this contact form Arjan de Goede [Fluor] MM711: sometimes no dialtone October 6, 2009 06:44 AM (in response to Arjan de Goede) This morning one of the ports looses dial tone again, while the
If the problem continues, replace the circuit pack. The 1392 is because the station is set as a TTI port and the test does not execute on it. Name Result Error Code 02A13 IPMEDPRO PASS 02A1301 MEDPROPT PASS 02A1302 MEDPROPT PASS release board 2a13 COMMAND RESULTS Port Maintenance Name Alt.
It's on a Cisco Catalyst. (I also did this prior to coming on-site, but forgot to mention it.) interface FastEthernet1/0/5 description CONNECTION TO AVAYA G650 2a13 switchport access vlan 2 speed Remotely test the terminal equipment. Sounds like there's no easy way to see if there's a device on an MM then. Issue the test board command.
Retry the command at 1-minute intervals no more than 5 times. Investigate user-reported troubles on this port by running other port tests, by examining station wiring, or by inspecting the station. This error indicates that the test is not valid for the particular maintenance object and can be ignored. navigate here should be in y to work.
Let's try bouncing the IP switchport: switch(config)#int fa1/0/5 switch(config-if)#shutdown switch(config-if)#no shutdown switch(config-if)#exit switch(config)#exit Observed no link-light on ip switch. Digital Station Audits Test (#17) This is a series of six tests that are classified as audits. To enable the test for a particular station being tested, enter change station extension.